ELIMSTAT~ LX Conductive Coating ITEM #K4093 ELIMSTAT LX is a water based conductive coating, manufactured with high quality acrylic latex. When applied to non-conductive surfaces, such as floors, bench tops, tote boxes, etc., ELIMSTAT LX provides conductivity to dissipate static charges. ELIMSTAT LX, along with appropriate LEGGE personnel body grounding devices, will provide a static free environment. ELIMSTAT LX is extremely cost effective. Cost per square foot is only a small fraction of the cost of conductive vinyl flooring and epoxy. ELIMSTAT LX is easy to apply, maintain and repair. Provides excellent wearability and detergent resistance. Like any conductive surface, ELIMSTAT LX must be tested regularly (NFPA-CODE #99) and maintained with proper maintenance products. Improper maintenance methods and products can block the conductivity and cause irregular test readings.

CONVENTIONAL SPRAY: DeVilbiss MBC-5 10 Spray Gun "E", Fluid tip and needle and #704, 765 or 78 Air Cap
AIRLESS SPRAY: DeVilbiss ICA-5026 spray gun and a spray cap or suitable orifice diameter 0.020-0.025.
MODEL LA I FLOOR CONDUCTIVITY TEST: Walter G LEGGE Co. Used in the testing of floors to comply with NFPA Code #99.
LEGGE PERSONNEL GROUNDING DEVICES: Full line of wristats, legstats, conductive shoes, hoots, and static dissipative shoes.

ELIMSTAT LX SPECIFICATIONS
COATING TYPE:Water based acrylic conductive coating
COVERAGE:300 400 square feet per gallon
CONDUCTIVITY:Meets NFPA Code #99 (#56) Specification of Conductive flooring, MIL SPEC DOD-HDBK-263. Meets and supersedes MIL-B8 1 705C for static decay.
RESISTANCE:25,000 to 1,000,000 ohms. Conductivity may be adjusted to customer specifications.
COLORS:Maroon, Green, Grey, Lt. Grey, Black
VEHICLE TYPE:Pure waterborne Acrylic resin
PIGMENT TYPE:Lead free, iron oxide, titanium dioxide and extenders.
FLASH POINT:None
DRY FILM THICKNESS and THEORETICAL COVERAGE:Up to 400 square feet per gallon at 1.5 mils dry film thickness.
VISCOSITY:1000 - 1500 ups
AVERAGE DRYING TIME:@ 75"F and 50% R.H.: I hr to the touch first coat, recoat after 3 4 hours
THEORETICAL SOLIDS BY VOLUME:33-36%
pH:8.3
WEIGHT:8.8 pounds per gallon

A water based acrylic, conductive coating reinforced with waterborne urethane for air dry applications. ELIMSTAT LXU is specifically designed for high performance use where hardness, chemical and abrasion resistance as well as exceptional adhesion properties are desired. Has excellent UV resistance and may be used as an exterior coating. Outstanding resistance to chemicals and solvents, with permanent conductivity: 25,000 1,000,()00 ohms (NFPA Code # 99). ELIMSTAT LXU is an excellent choice for difficult applications and offers a high-quality conductive coating for areas where additional adhesion and durability are required. May be rolled, brushed or sprayed. Two, 1.5 mil dry film coats recommended tar extended wear. Dry to touch in 45 minutes, recoat in 5-6 hours (24 hours if possible).

ELIMSTAT LXU SPECIFICATIONS
COATING TYPE:Water based acrylic-urethanc reinforced conductive coating
COVERAGE:300-400 sq. ft. per gallon
CONDUCTIVITY:Meets NFPA code # 99 (#56) specification of conductive flooring. MILSPEC. DOD-HDBK #263. Meets and supersedes MIL-B81705C for Static decay.
RESISTANCE:25,000 - 1,000.000 ohms
COLORS:Maroon, Green, Grey, and Black VEHICLE TYPE:Waterborne acrylic resin reinforced with urethane
PIGMENT TYPE:Lead free, iron oxide, titanium dioxide and extenders
FLASH POINT:None
DRY FILM THICKNESS:1.5 mils
VISCOSITY:1200- 1500 CPS
SOLIDS:35%-40%
pH:8.3
WEIGHT:8.8 lbs per gallon

The following group of coatings are formulated with a new development in conductive static dissipative coatings. All of these products are based on the highly advanced coating technology of metalized formulations. Coatings manufactured with this technology do not contain carbon black. They have permanent conductivity and are insensitive to humidity. The readings are easily controlled and formulated with the desired range.

ELIMSTAT SD Static Dissipative Coating
ELIMSTAT SD is a water based static dissipative coating, manufactured with high quality acrylic latex. ELIMSTAT SD provides permanent static dissipation to a variety of surfaces and areas. The applications are limitless, but some include - floors, walls, ceilings, printed circuit boards, containers, plastic surfaces, etc. - anywhere static dissipation is desired. When used with LEGGE grounding devices, ELIMSTAT SD provides a static free work environment.

The coating may be applied with roller, brush or sprayer. Surfaces should be clean and dry. Two coats minimum are required, 3 4 hours is the normal drying time between coats. Like all static dissipative surfaces ELIMSTAT SD must be tested regularly and maintained with proper maintenance products. Improper maintenance methods and products can block the conductivity and cause irregular readings. Concrete, tile and terrazzo floors with heavy dirt and grease build-up should be cleaned with TEXSPAR PLUS and STRIPPER #457. Floors must be rinsed and dried thoroughly before applying ELIMSTAT SD. ELIMSTAT SD is available in a variety of colors, including: BLUE- GREEN-GREY-BLACK-WHITEYELLOW-RED. Floors must be tested after 24 hours to ensure that surface resistivity is between 107 and 109 ohms/square inch in compliance with ASTM D-257-80 test method. STAT LES CLEANER: Floors coated with ELIMSTAT SD or STAT-LES may be maintained, as required, by damp mopping with a solution of STAT-LES CLEANER. Properly diluted (2 4 oz/gal) this method is very cost effective since it does not require rinsing and will not affect the conductivity of the floors.

ELIMSTAT SD SPECIFICATIONS
COATING TYPE:Water based acrylic static dissipative coating
COVERAGE:300 - 450 square feet per gallon
CONDUCTIVITY:Static dissipative coating for the electronics industry requirements. Meets and exceeds MIL-B81705B for static decay.
COLORS:White, grey, green, red, blue, tan, black, yellow
VEHICLE TYPE:Acrylic resin, waterborne
PIGMENT TYPE:Lead free, iron oxide, titanium dioxide and extenders
FLASH POINT:None
DRY FILM THICKNESS:1.5 mils per coat VISCOSITY:1000 1500CPS AVERAGE DRYING TIME:@ 75" F 50% R.H.: 1 hr to the touch first coat, recoat after 3 4 hours.
THEORETICAL SOLIDS BY WEIGHT:33-36%
pH:8.3
WEIGHT:8.9 LBS. per gallon
 

ELIMSTATX SDSC 549411 Static Dissipative Coating
ELIMSTAT SDSC 549411 is a static dissipative, super reflective, white, water-based acrylic coating designed for high performance uses in accordance with aerospace specifications. The product is used to coat Space Launch Vehicles and motors to reduce static electricity build up. LEGGE has worked closely with the aerospace industry to develop and test this coating and it is specified and used extensively by contractors and sub-contractors on rocket motors and assemblies in the aerospace industry.

ELIMSTAT SDSC SPECIFICATIONS
COMPOSITION:Pure Acrylic Latex
FINISH:Flat
DRYING TIME:Flat 45 min. to touch @ 75 degrees F. 50% relative humidity
REDUCER:1/2 pint water/gal
APPLICATION CONDITIONS:up to 85% RH, 50-100deg. F
SUBSTRATE (SURFACE) TEMP:above 50° F
TOTAL SOLIDS:58 - 63% (% non-volatile by weight)
WEIGHT PER GALLON:12.4 - 13.0 lbs
pH:8.5
VISCOSITY:5750-6050 cps @ 258deg C, Brookfield Viscometer with spindel #3 at 20 rpm
STORAGE TEMP (INDOORS):50 - 80 F
SHELF LIFE:6 months at recommended storage conditions

ELIMSTAT® UXM-60P
ELIMSTAT UXM-60P, conductive coating, is designed for high performance uses where hardness, chemical and abrasion resistance as well as exceptional adhesion properties are desired. ELIMSTAT UXM-60P has excellent UV resistance and can be used as an exterior coating. Outstanding resistance to chemicals and solvents, with permanent conductivity - adjustable to your Specifications. ELIMSTAT UXM-60P may be used for many difficult applications and offers a high quality Conductive coating for areas where adhesion is a problem. May be rolled, brushed or sprayed. Excellent recoatability, clean surface thoroughly with LEGCLEAN, allow to dry thoroughly and reapply ELIMSTAT UXM-60P.
ELIMSTAT® UXM-60P SPECIFICATIONS
COMPOSITION:Waterborne urethane, leveling agent, conductive agents
PERCENT SOLID:44-46%
SPECIFIC GRAVITY:1.02
pH:9.02
VISCOSITY:Brookfield #3 Spindle at 50 RPM - 440 CPS
WEIGHT PER GALLON:8.82 lbs
RECOATABILITY:excellent
WATER RESISTANCE:excellent
FREEZE/THAW:3 cycles
COVERAGE: 400 sq ft gallon
COLORS:Grey, Green, Blue, Tan, Yellow, White

ELIMSTATX® UXM-600
A water-borne urethane conductive coating with permanent conductivity. ELIMSTAT UXM-600, is specifically designed for high performance uses. Designed for use where hardness, chemical and abrasion resistance as well as exceptional adhesion properties are desired. ELIMSTAT UXM-600 has excellent UV resistance and can be used as an exterior coating. Outstanding resistance to chemicals and solvents, with permanent conductivity - adjustable to your specifications. ELIMSTAT UXM 600 is an excellent choice for G-10 and many difficult applications and oflers a high quality conductive coating for areas where adhesion is a problem May be rolled, brushed or sprayed. May be baked at temperatures up to 300 F.
ELIMSTAT® UXM-600 SPECIFICATIONS
TOTAL SOLIDS:30% (depending on conductivity)
pH:9.0
WEIGHT PER GALLON:8.5
FLASH POINT F. PENSKY:no flash point
Martens closed cup
FREEZE/THAW STABILITY:Passes 5 cycles
ACID NUMBER ON SOLIDS:30
COLORS:Clear & Black
VISCOSITY:Black-560 CPS. Clear-120 CPS

 

STAT-LESS 24% or 18% STATIC DISSIPATIVE FLOOR FINISH Formulated with conductive polymers to both reduce tribo-electric charging and create a static dissipative surface. Use on conventional tile to create a static dissipative surface. May also be used to protect static dissipative tiles without affecting readings. Provides excellent gloss to any surface. Metal cross-link, acrylic copolymers provide excellent durability in any interior environment. STAT-LES is easy to apply with a mop and is easily removed with STAT-LES STRIPPER. Maintain your STAT-LES treated floor with the complete STAT-LES SYSTEM for ease of maintenance and longevity. STAT-LESS 24% or 18% SPECIFICATIONS TYPE: Metal cross link acrylic copolymer SOLIDS:24% or 18% DENSITY:% 8.63 pounds/gallon SPECIFIC GRAVITY: @ 60deg F - 1.037 OVEN STABILITY:ANSI/ASTMD 1791 66 (accelerated aging of water emulsion floor polishes) - no change CONDUCTIVITYRANGE:Static Dissipative STATIC DELAY: 07 seconds (Mil-B-81705B-5kV charge to 0 kV)

Floors to be coated with ELIMSTAT® LX, ELIMSTAT®SD, ELIMSTAT® LXU, ELIMSTAT® SDU, or ELIMSTAT® UXM must he clean and dry and free of all oil grease release agents etc. Coatings may be applied with brush roller or spray. Additional information and details on installing LEGGE Coatings is available upon request. Please ask for Application.

Concrete tile and terrazzo floors with heavy dirt or grease build up should be cleaned with LEGGE's TEXSPAR® and STRIPPER #457. Surfaces must he rinsed and thoroughly dry before applying LEGGE coatings. Two coats are recommended to providle optimum conductivity and durability. Top coat of STAT-LES® or URE-STAT floor finish may be applied to provide higher gloss and added protection if desired. All floor care products available in 1, 5, and 55 gal. containers.